|  |
| Product Detail |
|
EPS-H104NV1
 - EPS-H104NV1
-- 12"
Hardwired Power Strip with
4 Outlets
This hard wired type power strip is good for
installation in your kitchen, cabinet, on the rack and so on. It
is not for normal wall outlets. There is no power cord and plug
with this unit.
Features
- 12" (0.30m) Durable Metal Housing Power
Strip
- 4 Black US Standard Outlets, Vertical Outlet
Orientation
- Hard Wired without Power Cord for Mounting at Your
Desired Location
- 6 Easily Punched off Knockouts on Each Side - on Top, Both
Sides, the Bottom Cover and Both Ends
- ETL Approved and Listed (Conforms to UL5
and CAN/CSA C22.2 No. 62)
- Easy Installation
- Wires Readily Striped for Easier Removal and Faster
Installation - Higher Efficiency
|
Model #:
|
EPS-H104NV1
|
|
Description:
|
12" 4 Outlet Hardwire Type
Metal Power Strip
|
|
Power Strip Measurement:
|
L12" x W1.614" x H1.535" (305
x 41 x 39mm) *
|
|
Outlets:
|
4
|
|
Outlet Color:
|
Black
|
|
Outlet Orientation:
|
Vertical
|
|
Receptacle Type
|
NEMA 5-15R
|
|
Outlet Spacing:
|
1.30/2.28" or 33/58mm (center
to center)
|
|
Knockout Cord Exit:
|
6 (Top, Bottom Cover, Both
Sides & Both Ends)
|
|
Voltage Input/Output:
|
110-125V 60Hz
|
|
Current Input:
|
15A
|
|
Full Load:
|
1875VA
|
|
On/Off Switch:
|
N/A
|
|
Circuit Breaker:
|
N/A
|
|
Surge Protection:
|
N/A
|
|
Indicators:
|
N/A
|
|
Mounting Tabs:
|
N/A
|
|
Mounting Clips:
|
2 x
¾" (19mm) Spring Clips (Click here) |
SAFETY WARNING:
Installation work of this unit must be done by a
professional, a licensed electrician or an electric
engineer.
Never install this unit during a thunder storm.
Switch off the power before you start installation work.
This unit is for indoor use only.
This unit is not intended for use in or around wet or
potentially wet areas including, but not limited to,
aquariums, saunas, showers and fountains.
Risk of Electric Shock!
INSTALLATION Guideline:
Before
installation, you will need to get a 3/8"
wire clamp connector (also known as Romex
Connector) and 3
wire connectors (also referred to as
terminal connectors. Decide your wire gauge, and ask
store attendant for assistance what color of connectors
you should get) from your local hardware or electric
supply or home improvement stores.
Minimum tool required: A fine to medium fine philips screw
driver, and a pair of scissors, and a pair of mid size slip
joint pliers
- Turn off electricity in the house
- Decide where to place this unit
- Choose the right side for cord exit and mark on the knockout coin
- Gently punch off the knockout coin marked earlier with
the back of a screw driver or other tool handy
- Unscrew the cover off the back of the power strip with a
philips screw driver
- Take out the white plastic insulation sheet, then use
the pair of scissors to cut a hole (about ¾" in
diameter, or big enough for the wires to go through) on
this white plastic insulation sheet WHERE the wires will
run through. (If you decide to use the bottom knockout on
the back cover for wire connection, the hole should be in
the middle of the sheet. Or, on the side.)
- Put the 3/8"
wire clamp connector you already have in place. The
big ring screw inside the wall and the two screws outside
the wall. Secure the installation of the clamp connector
by tightening the big ring screw from inside the wall with
the pair of slip joint pliers
- Run the wires through the
wire clamp connector, from the outside into the
power strip
- Please remember to run through the wires through the
white plastic insulation sheet
- Match the color of the wires and secure the wire
connection with proper
wire connectors (different wire gauge use different
colored wire connectors)
- Tighten the two screws properly on the
wire clamp connector
- Put back the insulation sheet back in place
- Screw the back cover on
- Mount the power strip where you want it to be:
A) For power strips with mounting tabs on both ends: screw
down the unit on the floor, wall or in your cabinet or on
your rack, where you want it to be
B) For power strips without mounting tabs, but to be
mounted with clips, place the unit where you want it to be
first, draw a line so that you know where to install the
clips. Place clips about 6" away from each end, and screw
the clips down with screws provided. Then, snap the power
strip in
- Turn electricity back on, you are ready to go
Note:
* For installation purpose: The
length of the power strip does not include the mounting tabs
(approx. 0.624"/15.8mm on both ends, if available, please
check the above spec chart); the width does not include the
size of screws (min. 0.064"/1.6mm on each side); the height
does not include the receptacles (about 0.208"/5.3mm above
the surface of the strip).
We also custom manufacture for
our customers.
▲
top ------------
| | Show Related Products |
|
