|  |
Click here for bigger image
 | | Product Name: | EPS-H412NVG1 -- 48" 12 Outlet Hardwired Metal Power Strip, Beige | | Our Price: | $29.99 | | Availability: | In Stock | | Product Number: | EPS-H412NVG1 | | Rating: |  |
|  |
| Product Detail |
|
EPS-H412NVG1
- EPS-H412NVG1
-- 48" Metal
Power Strip with 12 Outlets,
Hardwired Type, Beige
This hard wired type power strip is good
for installation in your kitchen, cabinet and so on. It is not for
normal wall outlets. There is no power cord and plug with this unit.
Features
- 4 ft (1.22m) Durable
Metal Housing Power Strip, Beige
- 12 Ivory US
Standard Outlets, Vertical
Outlet Orientation
- Hard Wired without
Power Cord for Mounting at Your Desired Location
- 6
Easily Punched off Knockouts
on Each Side - on Top, Both Sides, the Bottom Cover and Both Ends
- Easy
On/Off Back
Cover (only 4 Screws), No Need to Uncover he Whole Unit, Less Screws to Work on
- Wires Readily Striped for Easier Removal and Faster Installation
- Higher Efficiency
- Installation by professional
electricians only (OR DANGER:
Electric Shock)
|
Model #:
|
EPS-H412NVG1
|
|
Description:
|
48” 12 Outlet Hardwire
Type Metal Power Strip, Beige
|
|
Power Strip Measurement:
|
L48" x W1.614" x H1.535”
(1219 x 41 x 39mm) *
|
|
Outlets:
|
12
|
|
Outlet Color:
|
Ivory
|
|
Outlet Orientation:
|
Vertical
|
|
Receptacle Type
|
NEMA 5-15R
|
|
Outlet Spacing:
|
3.47/3.74" or 88/95mm
(center to center)
|
|
Knockout Cord Exit:
|
6
(Top, Bottom Cover,
Both Sides & Both Ends)
|
|
Voltage Input/Output:
|
110-125V 60Hz
|
|
Current Input:
|
15A
|
|
Full Load:
|
1875VA
|
|
On/Off Switch:
|
N/A
|
|
Circuit Breaker:
|
N/A
|
|
Surge Protection:
|
N/A
|
|
Indicators:
|
N/A
|
|
Mounting Tabs:
|
N/A
|
|
Mounting Clips:
|
2 x ¾” (19mm)
Spring Clips (Click here) |
INSTALLATION
PROCEDURE:
Before installation, you will need to get a 3/4" wire
clamp and 3
wire connectors from your local hardware or
electric supply or home improvement store.
Minimum tool required: A fine to medium fine philips screw driver
- Turn off
electricity in the house
- Decide where
to place this unit
- Choose the
right side for cord exit and mark on the knockout
coin
- Gently punch
off the knockout
coin marked earlier with a screw driver or other
tool handy
- Unscrew the cover
off
the back of the power strip (4 screws only) with a philips
screw driver
- Install the
3/4"
wire clamp you already have (the big ring screw inside the wall and
the
two pressure screws outside the wall)
- Run the wires
through the wire clamp
- Match the
color of the wires and connect them properly with terminal connectors
- Tighten the wire
clamp properly
- Put the
back
cover on
- Mount the
strip where you want it to be
- Turn
electricity back on, you are ready to go
WARNING:
You must be an electrician
or an
electric engineer to do the installation work.
Note:
* For installation purpose: The length of the power strip does not
include the mounting tabs at both ends; The width does not include the
size of screws; The height does not include the receptacles.
Important:
This unit is not
intended for use in or around wet or potentially wet areas including,
but not limited to, aquariums, saunas, showers and fountains.
We also custom
manufacture for our customers.
▲top------------
| | Show Related Products |
|
